Timber Care & Maintenance
Care & Maintenance of Timber Flooring

Timber flooring and decking are long term investments and with a small amount of care and maintenance optimum performance and enjoyment is ensured.

We recommend flooring and decking care is discussed with the installer or builder if possible to obtain maintenance procedures from the manufacturer of the chosen floor finish. However, the following care and maintenance hints will assist in keeping timber flooring and decking looking their best.


General Precautions & Maintenance Tips

Wait 48 hours from application of the last coat of varnish before placing furniture - not applicable to pre-finished floors.
Fit protective pads to furniture legs to reduce risk of marking the floor. To protect the floor surface use protective mats for furniture with castors. Barrel castors are less likely to damage a floor than ball castors. Wait 7 days from application of the last coat - not applicable to pre-finished floors
Don't place rugs on the floor for at least 2 weeks after the final coat is applied to ensure the finish is completely cured. Lay rugs over the clean floor so dirt is not trapped underneath.
Dirt and grit can lead to excess wear and scratching of a hardwood timber floor. Use dirt trapping mats at all exterior doors to minimise dirt, sand and grit that might be brought inside. Small rugs and hall runners are also helpful for collecting the dirt that can scratch a hardwood timber floor. Regularly sweep high traffic areas with a soft bristle broom or electrostatic mop.
All hardwood timber floors will fade, darken or change shades over time. Exposure to sunlight will increase this process. Rotate rugs periodically and protect the floor from direct sunlight with curtains or blinds.
In areas where extreme temperature changes or moisture variation are common, gaps or cupping may appear in the floor. Maintain an ambient temperature to avoid dryness that may causes gaps, and moisture increases that may cause cupping.
High heel shoes can dent a hard floor surface. Special care should be taken to remove shoes that have exposed heels with sharp points to avoid potential damage to a hardwood timber floor.
Pets with long nails or claws can scratch and dull the floor finish, make sure pets nails or claws are trimmed regularly and kept blunt.
One of the benefits of a hardwood timber floor is that it can be refinished if it becomes excessively scratched or dented. Boral Timber recommends the use of a flooring professional proficient in sanding and finishing to complete this work.

Cleaning Tips

A hardwood timber floor will look better for longer if it is kept as clean as possible. To remove surface dirt and grit, regularly vacuum, with a soft bristle head or an electrostatic attachment, or sweep with an electrostatic mop. Keep door mats clean.

For stubborn dirt, damp-mop the floor using a well rung mop. The use of a pH neutral floor cleaner can help remove stubborn dirt (use as per manufacturer's instructions).

Never clean a floor with common household detergents, polishes, steel wool pads, wax or similar products. These products can be too abrasive and scratch the surface, or may make a floor dangerously slippery. Some products may leave a film of silicon or wax on the timber which may hamper recoating of your floor in the future. Never use Methylated Spirits or Kerosene, as any type of petroleum distillate will degrade the coating and irreversibly dull the floor. Only use a pH neutral floor cleaner as per manufacturer's instructions.

Use only quality lint free floor mops and thoroughly wash new mops to remove any lint.

Wipe up spills and leaks promptly with a dry cloth or dry paper towel. For sticky substances, moisten the cloth slightly

Over wetting a floor when mopping or cleaning can change the moisture balance and cause a floor to expand, with some resulting in cupping. For this reason, it is important to ensure that mops and cloths are well wrung so that as little water solution as possible wets the floor.

Steam mops are not recommended for cleaning timber floors. Steam (moisture) is forced into the joints of the timber and any small incisions, breaks or cracks on the timber floor surface resulting in unusual reactions in the timber such as cupping. The heat from the steam mop could also cause damaged to the coating on the floor.Wood Floor Cleaner

Bona Wood Floor Cleaner is a ready-to-use waterborne cleaner designed for the on-going maintenance of finished timber floors. 

It is available in a 1 Litre spray or economical 2.5 Refill Packs




Mops & refills in stock at

Valley Floor Sanding Supplies

Loba Hardwood Floor Cleaner

Recommended Use:
Cleaning of cork and wood floors and other hard and elastic floors as well as doors or other water-proof hard surfaces.


Easy to use
Dries without streaks
Does not leave any residue
Environmentally friendly

Care & Maintenance of Decking

In order to keep a hardwood timber deck looking its best, it must be kept clean and well maintained. It is a good idea to inspect a hardwood timber deck at least annually to ensure that it is in good condition.

The deck must be regularly maintained as it may become discoloured or affected by moisture and weather. Inspect the deck to replace loose boards and protruding nails or screws. Any loose or damaged boards should be resecured or replaced, loose nails hammered back in or screws refixed.

To clean the deck, sweep off any loose dirt or garden residue and then clean the deck with a specialised deck cleaning product. It is important to not only remove dirt, but any algae or moss that may be growing on the deck. After the cleaning has been completed, lightly sand the deck in the direction of the timber. This will remove any splinters and damage to the timber.

Once cleaned, reseal the deck with a penetrating oil.  Before the decking finish is applied, cover areas around the deck that need protection such as plants and furniture. Drying times are dependent on the type of finish so check manufacturer's recommendations before walking on a newly finished deck. Apply and re-apply decking finish as per manufacturer's recommendations. Manufacturers may recommend that the decking finish needs to be re-applied more than once a year.

After a new timber deck has been built, or an existing deck repaired, thoroughly sweep and clean to remove metal filings from drilling, nailing or other construction that may cause black spots on the hardwood deck when exposed to the elements.

If the deck has turned grey from natural weathering or is discoloured due to metal filings or other construction materials, there are a large range of maintenance and cleaning products on the market which can bring back the timber's original colour. Use with care and follow the finish manufacturer's instructions carefully.